← All posts
Maintenance Troubleshooting

Motor and Drive Fault Troubleshooting, Check by Check

Motor and drive fault troubleshooting in order: rule out mechanical causes, then check supply, wiring, and starting parts before touching settings.

Workbench beside a stalled conveyor motor with terminal cover off, coupling guard pulled back, open blank notebook, pencil and coiled meter leads on steel.

Motor and Drive Fault Troubleshooting: A Check-by-Check Guide for Technicians

Motor and drive fault troubleshooting starts with the symptom. A motor that hums but will not turn usually has a mechanical jam, a missing phase or low voltage, or a failed starting component, so isolate power, then check whether the load moves freely before testing electrics. A drive that trips on overcurrent usually has a load too heavy at start, a short in the motor cable or winding, or acceleration settings that are too aggressive, so check the mechanical side and wiring before changing parameters.

Isolate and sort the fault before you test anything

Good troubleshooting begins with a precise description of what the machine is doing, because the symptom decides which checks come first. Write down the exact behaviour before anyone opens a panel: a hum with no rotation, a trip the moment the start command is given, a trip that appears after several minutes of running, or heat that builds until the machine shuts down. These four patterns point in different directions, and confusing them sends the technician down the wrong path.

Describe the symptom exactly: hum, trip, heat, or no start

Sort the fault into one group. A no-start means nothing happens when the start command is given. A hum-and-stall means the motor makes noise and does not turn. A trip on start means the drive faults as it begins to accelerate. A trip under load means the machine runs normally and then faults when the load rises. Note the time from command to fault, the load state at that moment, and whether the fault repeats after a reset. These details cost little to record, and they narrow the causes quickly.

Follow your site's isolation and lockout procedure first

Safety comes before any hands-on check. Confirm the machine is isolated and de-energised according to your site's rules, including lockout and verification of zero energy, before you open enclosures or take measurements. Capacitors and drives can hold stored energy after the supply is off, so wait for the time your drive manual specifies. This guide describes the order of diagnosis. It does not replace your site's lockout procedure, permit-to-work system, or the OEM's safety instructions.

Motor hums but will not turn

A humming motor that does not rotate usually has power but not enough torque to start. The rotor is trying to turn, so the fault often sits in the load, the bearings, or the starting circuit rather than in the supply itself. The order of checks matters. Mechanical causes are quick to test and can be ruled out without energising the machine, so they come first.

Mechanical causes to rule out before electrical ones

With the machine isolated, try to turn the driven shaft or coupling by hand, using the method in the approved manual. Look for a seized bearing, a jammed belt or gearbox, debris in a conveyor or pump, or a load that has shifted. A shaft that will not move means the electrical checks can wait, because a motor cannot start against a locked load however good the supply is. If the shaft turns freely, the mechanical side is cleared and you can move on. A failure here tells you the cause is in the load or bearings, which is the most common answer for this symptom.

Supply, phase, and starting-component checks

Once the load moves freely, check the supply. On a three-phase motor, a missing phase often produces exactly this hum: the motor runs on two phases with reduced torque and cannot start under load. Measure voltage across each pair of phases with the machine energised under your site's procedure, and compare the readings with the nameplate and the site manual. Low voltage under load is the next suspect. A supply that reads correctly with nothing running may sag once the motor draws starting current. On a single-phase motor, check the start capacitor and the centrifugal switch, since a failed starting component leaves the motor humming without enough start torque. A pass on each check removes one cause, and a fail points you to the component to repair or replace.

Drive overcurrent and trip causes

Overcurrent on a variable frequency drive means the output current has exceeded the limit the drive allows. The trip is a symptom of something the motor or load is demanding. Before you touch the parameters that govern current limits or ramps, find out when the trip happens, because timing separates the likely causes.

Trips on start versus trips under load

A trip on start usually points to something that stops the load from accelerating: a stuck load, a brake that has not released, or an acceleration ramp too short for the inertia being moved. A ground fault in the motor cable or winding can also trip the moment the output is energised. A trip under load usually points to a mechanical overload that builds slowly, such as a worn bearing that raises friction, a blockage that increases the load, or a drive that is undersized for the duty. A short table helps keep the patterns apart:

Pattern Check first
Trips at the start command Stuck load, brake, ramp time, cable and winding insulation
Trips after running, under load Bearings, load increase, cooling, drive sizing
Trips at the same point each cycle Load profile and process conditions

Cable, winding, and parameter causes

With the drive isolated, inspect the motor cable for damage, test its insulation and the winding with your site's method, and confirm connections at both ends. A ground fault or phase-to-phase short found here explains the trip directly. Only after the mechanical and wiring checks pass should you consider drive settings. Raising the current limit to stop the trip hides the cause and can damage the motor, the cable, or the drive. Any change to acceleration times or limits should follow the drive manual, and it should be logged in whatever record your site already keeps.

Overheating and shutdown: check in a fixed order

A motor or drive that overheats and shuts down often has a load problem, a cooling problem, or a supply imbalance. Check in a fixed order so you do not chase the wrong cause:

  1. Duty cycle and load. Confirm the machine is running within its rated duty. Compare current draw with the nameplate, and note whether the overheat follows a heavy part of the cycle.
  2. Ventilation and clearance. Check that vents, fins, and filters are clear, and that there is enough space around the motor and drive for air to move.
  3. Fan operation. Confirm the cooling fan turns and moves air. A failed fan can cause shutdown even under a light load.
  4. Supply balance. Measure voltage between phases. An imbalance raises losses and heat in the motor even when the total voltage looks acceptable.

If the overheating comes with falling hydraulic pressure, stop and treat it as a separate fault family with its own path. A hydraulic pump can give off heat that looks much like a motor or drive problem, and mixing the two wastes time.

Where a written checklist stops helping, and where a guided tool fits

A written checklist works well for a familiar machine that matches its manual. It helps less when the fault does not match the manual, when a technician arrives at an unfamiliar machine, or when experienced colleagues are not available to talk it through. In those cases the hard part is no longer knowing the steps. It is choosing the next one.

A guided tool can help order checks and show a reason for each. It does not replace the OEM manual or your site's safety rules. Treat its suggestions as a prompt for your own judgement and verification.

Fault Line AI is a web app that runs in a browser, and it covers four fault families with built-in checks: motor hum or no start, hydraulic pressure loss, drive overcurrent or trips, and overheating or shutdown. For motor hum and drive trips, each check comes with a reason, and when you mark a check as passed or failed, the list of causes re-ranks and the next check changes to match. A cause is marked as confirmed when its check passes. Other faults get a general list of checks. Guided troubleshooting works without an account, and its results are not saved. You can read more in Fault Line AI: Diagnose Machine Faults in Plain Words.

If you face a motor or drive fault on your next shift, run the guided troubleshooting in Fault Line AI. No sign-in is needed, but results are not saved, so write down the checks you ran. Teams that need shared access can look at the seat plans on the site.

Frequently asked questions

Why does a motor hum but not turn, and what should I check first?

The motor has power but cannot produce enough torque to start. Common causes are a jammed or seized load, a missing phase, low voltage under load, or a failed starting component on a single-phase motor. Isolate the machine, then turn the driven shaft by hand to rule out mechanical causes before testing the supply.

What causes a VFD overcurrent trip on start?

The usual causes are a stuck load or brake that stops acceleration, an acceleration ramp too short for the inertia, and a ground fault or short in the motor cable or winding. Check the mechanical side and the cable with the drive isolated before you raise any current limit.

Does Fault Line AI cover motor and drive faults like these?

Yes. Fault Line AI has built-in step-by-step checks for motor hum or no start and for drive overcurrent or trips, with a reason next to each check. It also covers overheating and hydraulic pressure loss, and other faults get a general list of checks.